Logo  
Circuit Monkey
Electronics for Hobbyists
CircuitMonkey.com
 
View Item

Boards      
DragonFly - ATmega1280 board


Features:
  • 80mm x 40mm (smaller than a credit card).
  • High Performance, Low Power AVRŽ 8-Bit Microcontroller
  • 86 programmable IO pins on 11 molex 2mm connectors.
  • 3.3V or 5V operation.
  • Programmable activity LED.
  • Power indicator LED
  • 2-pin Analog Reference input.
  • 128K (256K on 2560 model) Bytes of In-System Self-Programmable Flash
  • 4K Bytes EEPROM
  • 8K Bytes Internal SRAM
  • Optional Boot Code Section with Independent Lock Bits
  • JTAG Interface
  • Peripheral Features:
  • Four 8-bit PWM Channels
  • Twelve 16-bit PWM Channels
  • 16-channel, 10-bit ADC
  • Four Programmable Serial USART
  • Master/Slave SPI Serial Interface
  • 2-wire Serial Interface
  • More features detailed in the Atmel ATmega1280/2560 datasheet.




    "Drive up to 16 RC servos!"




    Item Not Currently Available.
    Item Number: 500-0028-01
     
    Price: us$59.90
    Shipping:  USA us$5.00 S/H Inside USA
    INTL (us$14.00 S/H Outside USA)
       

    This ATmega1280 based microcontroller board features 128K of flash for your most demanding applications. Measuring only 80mm x 40mm, the board is smaller than a credit card and two of these boards can fit in the palm of your hand.

    We pinned out all 86 of the IO pins on this chip. The board features an on-board 16MHz crystal. The board is powered by either an external 5V or 3.3V power source. It features a 6-pin ISP RobiCon connector for programming (adapter included) as well as a Molex 3-pin power connector (the third pin is reset).

    Drive up to 16 RC servos with this board. Perfect for Robotics, Hexapod. The "Naked" version of this board (no connectors soldered in) makes this board ultra thin and lightweight, making it perfect for UAV development.

    Arduino Mega
    compatible!

    We have a bundle that makes this board software compatible with Arduino Mega (which uses the ATmega1280 chip). Our bundle includes the board with Arduino firmware already loaded as well as a USB/Serial adapter and three 11-pin I/O cables.


    Recommended Cable Options:

  • 11-pin Molex to Bare Wires, 10cm
  • 11-pin Molex to 11-pin Molex, 10cm
  • 11-pin Molex to 11-pin Molex, 20cm
  • 11-pin Molex to Female Headers 5P/6P, 10cm
  • USB-A to 3-pin Molex, 5.5ft., Power Cable
  • 6-pin Molex to 3-pin/2-pin Molex, 10cm (for USB-Serial Adapter)
  • 6-pin Molex to 6-pin In-System-Programmer (use with Atmel MKII Programmer)

  • Other Accessories:

  • 11-pin/2-pin Breakout Board
  • This board is also available in a "Naked" Edition, lighter, thinner, and no connectors soldered in.


    Downloads
    Adobe PDF File 0028 DragonFly Schematic
      You will need the Adobe Acrobat Reader to view this file. Download it here
    Adobe PDF File 0028 DragonFly - Pin-Out Chart (with Arduino Pins)
      You will need the Adobe Acrobat Reader to view this file. Download it here






    UID: 000106